Journals
Perceived rain dynamics on hydrophilic/hydrophobic lens surfaces and their influences on vehicle camera performance.
Pao, W. Y., Li, L. and Agelin-Chaab, M. 2024.
Transactions of the Canadian Society for Mechanical Engineering. Accepted.
Evaluating weather impact on vehicles: a systematic review of perceived precipitation dynamics and testing methodologies.
Pao, W. Y., Mateus Carvalho, M., Farimah Hosseinnouri, F., Li, L., Clement Rouaix, C., Agelin-Chaab, M. et al. 2024.
Engineering Research Express, https://doi.org/10.1088/2631-8695/ad2033. Accepted.
Investigation of Thermal Properties of Phase Change Materials for Novel Hybrid Thermal Management Strategies for Cylindrical Li-ion Cells.
Shahid, S. and Agelin-Chaab, M. 2024.
Applied Thermal Engineering (2024) – Accepted
Investigation of Heat Transfer Enhancement Techniques on a Scalable Novel Hybrid Thermal Management Strategy for Lithium-ion Battery Packs.
Shahid, S. and Agelin-Chaab, M. 2024.
Batteries (2024) - Accepted
Experimental and Numerical Analysis of a Hybrid Thermal Management Concept at Different Discharge Rates for a Cylindrical Li-ion Battery Module.
Shahid, S. and Agelin-Chaab, M. 2024.
Batteries 9.9 (2023): 474. https://doi.org/10.3390/batteries9090474
Development and Analysis of Hybrid Cooling Concepts for an Electric Battery Pack.
Shahid, S. and Agelin-Chaab, M. 2024.
Journal of Energy Storage 73.A (2023): 108952. https://doi.org/10.1016/j.est.2023.108952
Exergoeconomic and exergoenvironmental analyses of a hybridized marine engine powered by eco-friendly fuels, including hydrogen.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Energy. Accepted.
Investigation of a Renewable Energy Based Integrated System with Carbon Capturing for Hydrogen, Methane, and Other Useful Outputs.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2023.
J. Clean Prod., Accepted.
Comparison of Hybrid Cooling Concepts with PCM Cooling for Electric Battery Packs.
Shahid, S. and Agelin-Chaab, M. 2023.
Journal of Fluid Flow, Heat and Mass Transfer, accepted.
Comparison Between Different PCM Mediums and Dielectric Fluid for Hybrid Thermal Management of Electric Battery Packs.
Shahid, S. and Agelin-Chaab, M. 2023.
Journal of Fluid Flow, Heat and Mass Transfer, Vol. 10, pp. 62-68.
Economic and Environmental Impact Assessments of a New Integrated Energy System for Ocean Applications.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Chemosphere, Accepted
Design and Analysis of a Hybrid Space Heating System Based on HT-PEM Fuel Cell and an Air Source Heat Pump with a Novel Heat Recovery Strategy.
Capuano, M., Sorrentino, M. and Agelin-Chaab, M. 2023.
Applied Thermal Engineering, Vol. 231, Volume 231, 120947, ISSN 1359-4311,
https://doi.org/10.1016/j.applthermaleng.2023.120947.
Analysis and comparison of innovative PEMFC systems coupled with an ASHP for space heating in cold climates.
de Fato, V., Agelin-Chaab, M. and Sorrentino, M. 2023.
e-Prime - Advances in Electrical Engineering, Electronics and Energy, Vol. 4, 100173, ISSN 2772-6711,
https://doi.org/10.1016/j.prime.2023.100173.
A Comprehensive Assessment of a New Hybrid Combined Marine Engine Using Alternative Fuel Blends.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Energy. In press.
Modeling of a New Fuel Cell Based Rail Engine System Using Green Fuel Blends.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Applied Thermal Engineering, In press.
Development of Intelligent Passive Device Generator for Road Vehicle Applications,
Aranha, R., Siddiqui, N. A., Pao, W. Y. and Agelin-Chaab, M. 2023.
J. Applied Fluid Mechanics, Vol. 16(8), pp. 1500-1514.
Design of a Multigenerational Energy System with Hydrogen Production for Clean Cement Plants.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2023.
J. Clean Prod. In Press. [11.072]
Investigation of the wake flow around the elliptical Ahmed body using detached Eddy simulation.
Siddiqui, N. A. and Agelin-Chaab, M. 2023.
International Journal of Heat and Fluid Flow. Vol. 101, In press [IF:2.643]
Environmental Impact Assessment of a Newly Developed Solid Oxide Fuel Cell-Based System Combined with Propulsion Engine Using Various Fuel Blends for Cleaner Operations.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Sustainable Materials and Technologies. Vol. 35, pp. e00554. [IF: 10.681]
Efficiency, Economic and Environmental Impact Assessment of a Newly Developed Rail Engine using Hydrogen and Other Sustainable Fuel Blends,
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
e-Prime - Advances in Electrical Engineering, Electronics and Energy. Vol. 3, In press.
An Innovative Study on A Hybridized Ship Powering System with Fuel Cells Using Hydrogen and Clean Fuel Blends.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Applied Thermal Engineering. Vol. 221, In press
Design and Assignment of a New Helical Fixed Bed Type CO2 Methanation Reactor.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2022.
Fuel Journal. Vol. 35, In press
Investigation and comparative evaluation of a hybridized marine engine powered by eco-friendly fuels including hydrogen.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Int. J. Hydrogen Energy, In press. [7.139]
Transport Phenomena Modeling of Various Novel Renewable Natural Gas Reactors and Reactor Configurations.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2022.
Chemical Engineering Science. In press. [IF: 4.889]
A review of thermal runaway prevention and mitigation strategies for lithium-ion batteries.
Shahid, S. and Agelin-Chaab, M. 2022.
Energy Conversion and Management.Vol. 16, 100310, In press.
Investigation of A Hybridized Combined Cycle Engine with SOFC System for Marine Applications.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Journal of Thermal Analysis and Calorimetry, In press. [IF: 4.629]
Flow Features of the Ahmed Body at a Low Reynolds Number.
Siddiqui, N. A. and Agelin-Chaab, M. 2022.
International Journal of Heat and Fluid Flow. Vol. 98, 109052, ISSN 0142-727X [IF:2.643]
Experimental investigation of the flow features around an elliptical Ahmed body.
Siddiqui, N. A. and Agelin-Chaab, M. 2022.
Physics of Fluids. Vol. 34, 105119, https://doi.org/10.1063/5.0114377
Weather Aerodynamic Adaptation for Autonomous Vehicles: A Tentative Framework,
Hangan, H., Agelin-Chaab, M., Gultepe, I., Elfstrom, G., Komar, J. 2022.
Transactions of the Canadian Society for Mechanical Engineering, Accepted.
A Soiling Mitigation Method to Enhance the Performance of ADAS in Precipitation,
Pao, W. Y., Li, L., and Agelin-Chaab, M. 2022.
SAE International Journal of Advances and Current Practices in Mobility, doi:10.4271/2022-01-0076.
Selected as one of the best papers for the SAE International - World Congress
Experience 2022.
Environmental Impact Assessment of a Newly Developed Solid Oxide Fuel Cell-Based System Combined with Propulsion Engine Using Various Fuel Blends for Cleaner Operations.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Sustainable Materials and Technologies, accepted [IF: 7.05]
Thermal Modeling and Analysis of an Electric Vehicle Charging System.
Chea, B., Agelin-chaab, M., Mastali, M. and Szymczyk, R., 2022.
Energy Technology, in press. [IF: 3.63]
Analysis of a Newly Developed Locomotives Employing Sustainable Fuel Blends with Hydrogen.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Fuel, Vol. 319, 123748. https://doi.org/10.1016/j.fuel.2022.123748 [IF: 6.61]
Development of a Hybrid Cooling Concept for Cylindrical Li-ion Cells.
Shahid, S., Chea, B. and Agelin-Chaab, M. 2022.
Journal of Energy Storage, Vol. 50, pp. 104214. https://doi.org/10.1016/j.est.2022.104214. [IF: 6.58]
Development and Analysis of a Clean Methane Production System.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2022.
Fuel, Vol. 317, 123396, ISSN 0016-2361, https://doi.org/10.1016/j.fuel.2022.123396. [IF: 6.61]
Economic and Environmental Impact Assessment of Hybridized Aircraft Engines with Hydrogen and Other Fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Int. J. Hydrogen Energy, Vol. 47(22), pp. 11669-11685, ISSN 0360-3199, https://doi.org/10.1016/j.ijhydene.2022.01.171. [IF: 5.82]
Analysis of an integrated thermal energy system for applications in cold regions.
Addo-Binney, B. and Agelin-Chaab, M. 2022.
J. Energy Resources Technology (ASME), Vol. 144(1), pp. 012104 (14 pages) [IF: 2.90]
Exergetic assessment of a newly designed solid oxide fuel cell-based system combined with a propulsion engine.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Energy, Vol. 239, Part D, pp. 122314, ISSN 0360-5442, https://doi.org/10.1016/j.energy.2021.122314. [IF: 7.15]
A Comprehensive Life Cycle Assessment of a Cascade Heat Pump and a Natural Gas Furnace.
Addo-Binney, B. and Agelin-Chaab, M., Bamfo, E., and Koohi, S. 2022.
Integrated Environmental Assessment and Management, Vol. 18, pp. 572 - 580. [IF: 2.99]
Exergetic, Exergoeconomic and Exergoenvironmental Analyses of a Hybrid Combined Locomotive Powering System for Rail Transportation.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy Conversion and Management, Vol. 245, pp. 114619. [IF: 9.71]
Analysis of ebike dynamics and cyclists’ anxiety levels and interactions with road vehicles that influence safety.
Pejhan, S., Agelin-Chaab, M., Yusuf, M., Eng., D. 2021.
Accident Analysis and Prevention, Vol. 159, pp. 106272 [IF: 4.99]
Investigation of Potential Fuels for Hybrid Molten Carbonate Fuel Cell-Based Aircraft Propulsion Systems.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy & Fuels, Vol. 35(12), pp. 10156–10168. [IF: 3.61]
Assessment of effectiveness of optimum physical distancing phenomena for COVID-19.
Chea, B., Bolt, A., Agelin-chaab, M. and Dincer, I., 2021.
Physics of fluids. Vol. 33, pp. 051903 [IF: 3.52]
Development of hybrid thermal management techniques for battery packs.
Shahid, S., and Agelin-Chaab, M. 2021.
Applied Thermal Engineering, Vol. 186, pp. 116542. [IF: 5.30]
Investigation of Two Hybrid Aircraft Propulsion and Powering Systems Using Alternative Fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy, Vol. 232, pp. 121037. [IF: 7.15]
Nature-inspired solutions to bluff body aerodynamic problems: A review.
Siddiqui, N. A. and Agelin-Chaab, M. 2021.
Journal of Mechanical Engineering and Sciences, Vol. 15(2), pp. 8095 - 8140. [IF: 0.41]
A review of unique aluminum-water based hydrogen production options.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2021.
Energy & Fuels, Vol. 35(2), pp. 1024–1040 [IF: 3.61]
Development and assessment of a cleaner locomotive powering system with alternative fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Fuel Journal, Vol. 296, pp. 120529 [IF: 6.61]
Novel hybrid aircraft propulsion systems using hydrogen, methane, methanol, ethanol, and dimethyl ether as alternative fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy Conversion and Management, Vol. 238, pp. 114172 [IF: 9.71]
A new integrated system with thermal energy storage for five useful outputs: A case study.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2021.
Sustainable Energy and Technology Assessment. Vol. 45, pp. 101116 [5.35]
A Simple passive device for the drag reduction of an Ahmed body.
Siddiqui, N. A., and Agelin-Chaab, M. 2021.
J. Applied Fluid Mechanics, Vol. 14(1), pp. 147-164. [IF: 1.41]
Ice Crystals and Snow Measurements from a Climatic Wind Tunnel to Atmospheric Field Studies,
Gultepe, I., Agelin-Chaab, M. et al., August 2021,
3rd International Summer Snowfall Workshop, UK.
Drag Reduction on a Square Back Ahmed Body Using a Simple Flap
Siddiqui, N. A. and Agelin-Chaab, M. June 2021.
In Proceedings of the 2021 CSME International Congress. University of PEI, Charlottetown, PEI, Canada.
Design of Aerodynamic Devices Using Genetic Optimization,
Aranha, R. and Agelin-Chaab, M. June 2021.
In Proceedings of the 2021 CSME International Congress. University of PEI, Charlottetown, PEI, Canada.
Fundamental and Parametric Considerations for Numerical Rain Simulation in a Wind Tunnel, In Proceedings of the 2021 CSME International Congress.
Pao, W. Y. and Agelin-Chaab, M. June 2021.
University of PEI, Charlottetown, PEI, Canada.
Pao, W. Y., Li, L. and Agelin-Chaab, M. 2024.
Transactions of the Canadian Society for Mechanical Engineering. Accepted.
Evaluating weather impact on vehicles: a systematic review of perceived precipitation dynamics and testing methodologies.
Pao, W. Y., Mateus Carvalho, M., Farimah Hosseinnouri, F., Li, L., Clement Rouaix, C., Agelin-Chaab, M. et al. 2024.
Engineering Research Express, https://doi.org/10.1088/2631-8695/ad2033. Accepted.
Investigation of Thermal Properties of Phase Change Materials for Novel Hybrid Thermal Management Strategies for Cylindrical Li-ion Cells.
Shahid, S. and Agelin-Chaab, M. 2024.
Applied Thermal Engineering (2024) – Accepted
Investigation of Heat Transfer Enhancement Techniques on a Scalable Novel Hybrid Thermal Management Strategy for Lithium-ion Battery Packs.
Shahid, S. and Agelin-Chaab, M. 2024.
Batteries (2024) - Accepted
Experimental and Numerical Analysis of a Hybrid Thermal Management Concept at Different Discharge Rates for a Cylindrical Li-ion Battery Module.
Shahid, S. and Agelin-Chaab, M. 2024.
Batteries 9.9 (2023): 474. https://doi.org/10.3390/batteries9090474
Development and Analysis of Hybrid Cooling Concepts for an Electric Battery Pack.
Shahid, S. and Agelin-Chaab, M. 2024.
Journal of Energy Storage 73.A (2023): 108952. https://doi.org/10.1016/j.est.2023.108952
Exergoeconomic and exergoenvironmental analyses of a hybridized marine engine powered by eco-friendly fuels, including hydrogen.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Energy. Accepted.
Investigation of a Renewable Energy Based Integrated System with Carbon Capturing for Hydrogen, Methane, and Other Useful Outputs.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2023.
J. Clean Prod., Accepted.
Comparison of Hybrid Cooling Concepts with PCM Cooling for Electric Battery Packs.
Shahid, S. and Agelin-Chaab, M. 2023.
Journal of Fluid Flow, Heat and Mass Transfer, accepted.
Comparison Between Different PCM Mediums and Dielectric Fluid for Hybrid Thermal Management of Electric Battery Packs.
Shahid, S. and Agelin-Chaab, M. 2023.
Journal of Fluid Flow, Heat and Mass Transfer, Vol. 10, pp. 62-68.
Economic and Environmental Impact Assessments of a New Integrated Energy System for Ocean Applications.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Chemosphere, Accepted
Design and Analysis of a Hybrid Space Heating System Based on HT-PEM Fuel Cell and an Air Source Heat Pump with a Novel Heat Recovery Strategy.
Capuano, M., Sorrentino, M. and Agelin-Chaab, M. 2023.
Applied Thermal Engineering, Vol. 231, Volume 231, 120947, ISSN 1359-4311,
https://doi.org/10.1016/j.applthermaleng.2023.120947.
Analysis and comparison of innovative PEMFC systems coupled with an ASHP for space heating in cold climates.
de Fato, V., Agelin-Chaab, M. and Sorrentino, M. 2023.
e-Prime - Advances in Electrical Engineering, Electronics and Energy, Vol. 4, 100173, ISSN 2772-6711,
https://doi.org/10.1016/j.prime.2023.100173.
A Comprehensive Assessment of a New Hybrid Combined Marine Engine Using Alternative Fuel Blends.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Energy. In press.
Modeling of a New Fuel Cell Based Rail Engine System Using Green Fuel Blends.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Applied Thermal Engineering, In press.
Development of Intelligent Passive Device Generator for Road Vehicle Applications,
Aranha, R., Siddiqui, N. A., Pao, W. Y. and Agelin-Chaab, M. 2023.
J. Applied Fluid Mechanics, Vol. 16(8), pp. 1500-1514.
Design of a Multigenerational Energy System with Hydrogen Production for Clean Cement Plants.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2023.
J. Clean Prod. In Press. [11.072]
Investigation of the wake flow around the elliptical Ahmed body using detached Eddy simulation.
Siddiqui, N. A. and Agelin-Chaab, M. 2023.
International Journal of Heat and Fluid Flow. Vol. 101, In press [IF:2.643]
Environmental Impact Assessment of a Newly Developed Solid Oxide Fuel Cell-Based System Combined with Propulsion Engine Using Various Fuel Blends for Cleaner Operations.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Sustainable Materials and Technologies. Vol. 35, pp. e00554. [IF: 10.681]
Efficiency, Economic and Environmental Impact Assessment of a Newly Developed Rail Engine using Hydrogen and Other Sustainable Fuel Blends,
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
e-Prime - Advances in Electrical Engineering, Electronics and Energy. Vol. 3, In press.
An Innovative Study on A Hybridized Ship Powering System with Fuel Cells Using Hydrogen and Clean Fuel Blends.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2023.
Applied Thermal Engineering. Vol. 221, In press
Design and Assignment of a New Helical Fixed Bed Type CO2 Methanation Reactor.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2022.
Fuel Journal. Vol. 35, In press
Investigation and comparative evaluation of a hybridized marine engine powered by eco-friendly fuels including hydrogen.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Int. J. Hydrogen Energy, In press. [7.139]
Transport Phenomena Modeling of Various Novel Renewable Natural Gas Reactors and Reactor Configurations.
Bolt, A., Dincer, I. and Agelin-Chaab, M. 2022.
Chemical Engineering Science. In press. [IF: 4.889]
A review of thermal runaway prevention and mitigation strategies for lithium-ion batteries.
Shahid, S. and Agelin-Chaab, M. 2022.
Energy Conversion and Management.Vol. 16, 100310, In press.
Investigation of A Hybridized Combined Cycle Engine with SOFC System for Marine Applications.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Journal of Thermal Analysis and Calorimetry, In press. [IF: 4.629]
Flow Features of the Ahmed Body at a Low Reynolds Number.
Siddiqui, N. A. and Agelin-Chaab, M. 2022.
International Journal of Heat and Fluid Flow. Vol. 98, 109052, ISSN 0142-727X [IF:2.643]
Experimental investigation of the flow features around an elliptical Ahmed body.
Siddiqui, N. A. and Agelin-Chaab, M. 2022.
Physics of Fluids. Vol. 34, 105119, https://doi.org/10.1063/5.0114377
Weather Aerodynamic Adaptation for Autonomous Vehicles: A Tentative Framework,
Hangan, H., Agelin-Chaab, M., Gultepe, I., Elfstrom, G., Komar, J. 2022.
Transactions of the Canadian Society for Mechanical Engineering, Accepted.
A Soiling Mitigation Method to Enhance the Performance of ADAS in Precipitation,
Pao, W. Y., Li, L., and Agelin-Chaab, M. 2022.
SAE International Journal of Advances and Current Practices in Mobility, doi:10.4271/2022-01-0076.
Selected as one of the best papers for the SAE International - World Congress
Experience 2022.
Environmental Impact Assessment of a Newly Developed Solid Oxide Fuel Cell-Based System Combined with Propulsion Engine Using Various Fuel Blends for Cleaner Operations.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Sustainable Materials and Technologies, accepted [IF: 7.05]
Thermal Modeling and Analysis of an Electric Vehicle Charging System.
Chea, B., Agelin-chaab, M., Mastali, M. and Szymczyk, R., 2022.
Energy Technology, in press. [IF: 3.63]
Analysis of a Newly Developed Locomotives Employing Sustainable Fuel Blends with Hydrogen.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Fuel, Vol. 319, 123748. https://doi.org/10.1016/j.fuel.2022.123748 [IF: 6.61]
Development of a Hybrid Cooling Concept for Cylindrical Li-ion Cells.
Shahid, S., Chea, B. and Agelin-Chaab, M. 2022.
Journal of Energy Storage, Vol. 50, pp. 104214. https://doi.org/10.1016/j.est.2022.104214. [IF: 6.58]
Development and Analysis of a Clean Methane Production System.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2022.
Fuel, Vol. 317, 123396, ISSN 0016-2361, https://doi.org/10.1016/j.fuel.2022.123396. [IF: 6.61]
Economic and Environmental Impact Assessment of Hybridized Aircraft Engines with Hydrogen and Other Fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Int. J. Hydrogen Energy, Vol. 47(22), pp. 11669-11685, ISSN 0360-3199, https://doi.org/10.1016/j.ijhydene.2022.01.171. [IF: 5.82]
Analysis of an integrated thermal energy system for applications in cold regions.
Addo-Binney, B. and Agelin-Chaab, M. 2022.
J. Energy Resources Technology (ASME), Vol. 144(1), pp. 012104 (14 pages) [IF: 2.90]
Exergetic assessment of a newly designed solid oxide fuel cell-based system combined with a propulsion engine.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2022.
Energy, Vol. 239, Part D, pp. 122314, ISSN 0360-5442, https://doi.org/10.1016/j.energy.2021.122314. [IF: 7.15]
A Comprehensive Life Cycle Assessment of a Cascade Heat Pump and a Natural Gas Furnace.
Addo-Binney, B. and Agelin-Chaab, M., Bamfo, E., and Koohi, S. 2022.
Integrated Environmental Assessment and Management, Vol. 18, pp. 572 - 580. [IF: 2.99]
Exergetic, Exergoeconomic and Exergoenvironmental Analyses of a Hybrid Combined Locomotive Powering System for Rail Transportation.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy Conversion and Management, Vol. 245, pp. 114619. [IF: 9.71]
Analysis of ebike dynamics and cyclists’ anxiety levels and interactions with road vehicles that influence safety.
Pejhan, S., Agelin-Chaab, M., Yusuf, M., Eng., D. 2021.
Accident Analysis and Prevention, Vol. 159, pp. 106272 [IF: 4.99]
Investigation of Potential Fuels for Hybrid Molten Carbonate Fuel Cell-Based Aircraft Propulsion Systems.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy & Fuels, Vol. 35(12), pp. 10156–10168. [IF: 3.61]
Assessment of effectiveness of optimum physical distancing phenomena for COVID-19.
Chea, B., Bolt, A., Agelin-chaab, M. and Dincer, I., 2021.
Physics of fluids. Vol. 33, pp. 051903 [IF: 3.52]
Development of hybrid thermal management techniques for battery packs.
Shahid, S., and Agelin-Chaab, M. 2021.
Applied Thermal Engineering, Vol. 186, pp. 116542. [IF: 5.30]
Investigation of Two Hybrid Aircraft Propulsion and Powering Systems Using Alternative Fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy, Vol. 232, pp. 121037. [IF: 7.15]
Nature-inspired solutions to bluff body aerodynamic problems: A review.
Siddiqui, N. A. and Agelin-Chaab, M. 2021.
Journal of Mechanical Engineering and Sciences, Vol. 15(2), pp. 8095 - 8140. [IF: 0.41]
A review of unique aluminum-water based hydrogen production options.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2021.
Energy & Fuels, Vol. 35(2), pp. 1024–1040 [IF: 3.61]
Development and assessment of a cleaner locomotive powering system with alternative fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Fuel Journal, Vol. 296, pp. 120529 [IF: 6.61]
Novel hybrid aircraft propulsion systems using hydrogen, methane, methanol, ethanol, and dimethyl ether as alternative fuels.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2021.
Energy Conversion and Management, Vol. 238, pp. 114172 [IF: 9.71]
A new integrated system with thermal energy storage for five useful outputs: A case study.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2021.
Sustainable Energy and Technology Assessment. Vol. 45, pp. 101116 [5.35]
A Simple passive device for the drag reduction of an Ahmed body.
Siddiqui, N. A., and Agelin-Chaab, M. 2021.
J. Applied Fluid Mechanics, Vol. 14(1), pp. 147-164. [IF: 1.41]
Ice Crystals and Snow Measurements from a Climatic Wind Tunnel to Atmospheric Field Studies,
Gultepe, I., Agelin-Chaab, M. et al., August 2021,
3rd International Summer Snowfall Workshop, UK.
Drag Reduction on a Square Back Ahmed Body Using a Simple Flap
Siddiqui, N. A. and Agelin-Chaab, M. June 2021.
In Proceedings of the 2021 CSME International Congress. University of PEI, Charlottetown, PEI, Canada.
Design of Aerodynamic Devices Using Genetic Optimization,
Aranha, R. and Agelin-Chaab, M. June 2021.
In Proceedings of the 2021 CSME International Congress. University of PEI, Charlottetown, PEI, Canada.
Fundamental and Parametric Considerations for Numerical Rain Simulation in a Wind Tunnel, In Proceedings of the 2021 CSME International Congress.
Pao, W. Y. and Agelin-Chaab, M. June 2021.
University of PEI, Charlottetown, PEI, Canada.
Investigation of the effectiveness of a passive device for soiling mitigation for vehicle side-cameras.
Collings, W., Pao, W., and Agelin-Chaab, M. 2020.
SAE Int. J. Adv. & Curr Prac. in Mobility, 2(6), pp. 3293 - 3300, https://doi.org/10.4271/2020-01-0699
Selected as one of the best papers for the SAE International - World Congress Experience 2020.
Experimental and Numerical Studies of a Soft Impact Piezoelectric Energy Harvesting Using an MR Fluid.
Azangbebil, H. K., Djokoto, S. S., and Agelin-Chaab, M. 2020.
IEEE Sensors Journal, Vol. 20(19), pp. 11204-11211 [IF: 3.30]
Design of a Multigenerational System with Absorption Cooling for a Residential Community: A Case Study.
Bolt, A., Chea, B., Dincer, I., Agelin-Chaab, M. and Rosen M. 2020.
J. Energy Resources Technology (ASME), Vol. 143(6), pp. 1–11.[IF: 2.90]
A Critical Review of Synthetic Natural Gas Production Techniques and Technologies.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2020.
J. Natural Gas Science and Engineering Vol. 84, pp.103670. [IF:4.97]
Development of Clean Power Plant Integrated with Solar Farm for a Sustainable Community.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2020.
Energy Conversion and Management, Vol. 225, pp 113434. [IF: 9.71]
Modelling and Study of Magnetorheological Fluid Impact Base Frequency Enhancement for a Micro-Piezoelectric Energy Generator.
Djokoto, S. S., Azangbebil, H. K., Agelin-Chaab, M., Dragasius, E. and Juresnas, V. 2020.
Int. J. Green Energy, Vol. 17(9), pp. 529-539.[IF: 2.46]
Controlling of vibrations in micro-cantilever beam using a layer of active electrorheological fluid support.
Djokoto, S. S., Dragasius, E., Juresnas, V., and Agelin-Chaab, M. 2020.
IEEE Sensors Journal, Vol. 20 (8), pp. 4074 - 4079.[IF: 3.30]
Thermodynamic Analysis of a hybrid energy system using geothermal and solar energy sources with thermal storage in a residential building.
Seyam, S., Dincer, I., and Agelin-Chaab, M. 2020.
Energy Storage, Vol. 2(1), pp. 1-22.
Analysis of a clean hydrogen liquefaction plant integrated with a geothermal system.
Seyam, S., Dincer, I., and Agelin-Chaab, M. 2020.
J. Cleaner Production, Vol. 243, pp. 118562 [9.30]
Experimental study of hydrogen production process with aluminum and water.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2020.
Int. Journal of Hydrogen Energy, Vol. 45(28), 14232–14244. [IF: 5.82]
Experimental Study of a Thermal Cooling Technique for Cylindrical Batteries.
Wei, Y., and Agelin-Chaab, M. 2020.
Journal of Electrochemical Energy Conversion & Storage (ASME), 17(2): 021102 (13 pages) [IF: 2.01]
Energy and exergy analyses of hydrogen production process with aluminum and water chemical reaction.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2020.
Energy, Vol. 205, pp. [IF: 7.15]
Development and Experimental Analysis of a Hybrid Cooling Concept for Electric Vehicle Battery Packs.
Wei, Y., and Agelin-Chaab, M. 2019.
J. Energy Storage,Vol. 25, pp.100906 [IF: 6.58]
An Integrated Heat Recovery and Storage System for a Residential Building.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2019.
Energy Storage, Vol. 1(5), pp. 1–13.
A Meteorological Supersite for Aviation and Cold Weather Applications.
Gultepe, I., Agelin-Chaab, M., Komar, J. et al. 2019.
Pure Appl. Geophys, Vol. 176 (5), pp. 1977– 2015. https://doi.org/10.1007/s00024-018-1880-3 [IF: 2.34]
Application of Jets and Vortex Generators to Improve Air-cooling and Temperature Uniformity in a Simple Battery Pack.
Shahid, S., and Agelin-Chaab, M. 2018.
J. Thermal Science and Engineering Applications (ASME), Vol. 11(2), doi:10.1115/1.4041493 (16 pages). [IF: 1.47]
Whole Building Optimization of a Residential Home with PV and Battery Storage in The Bahamas.
Bingham, R., Agelin-Chaab, M. and Rosen M. 2018.
Renewable Energy, Vol. 132, pp. 1088-1103 [IF: 8.00]
Laminar-Turbulent Transition Flows of Non-Newtonian Slurries: Models Assessment.
Adane, K.F.K., and Agelin-Chaab, M. 2018
J. Fluids Engineering (ASME), Vol. 141(1),011104 (10 pages). [IF: 2.00]
Thermal and Electrical Performance Assessments of Lithium-Ion Battery Modules for an Electric Vehicle Under Actual Drive Cycles.
Panchal, S., Mathew, M., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2018.
Electric Power Systems Research, Vol. 163, pp.18-27 [IF: 3.41]
Experimental and Numerical Studies on Air Cooling and Temperature Uniformity in a Battery Pack.
Shahid, S., and Agelin-Chaab, M. 2018.
Int. J. Energy Research., Vol. 42(6), pp. 2246-2262 [IF: 5.16]
Experimental Investigation of a Novel Hybrid Cooling Method for Lithium-ion Batteries.
Wei, Y., and Agelin-Chaab, M. 2018,
Applied Thermal Engineering, Vol. 136,375-387 [IF: 5.30]
Design and Simulation of a Lithium-ion Battery at Large C-Rates and Varying Boundary Conditions through Heat Flux Distributions.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2018.
Measurement, Vol. 116, pp. 382-390. [IF: 3.93]
Development and analysis of a technique to improve air-cooling and temperature uniformity in a battery pack for cylindrical batteries.
Shahid, S., and Agelin-Chaab, M. 2018.
Thermal Science and Engineering Progress, Vol. 5, pp. 351-363.
Analysis of Cooling and Temperature Uniformity Effectiveness in a Battery Pack for Cylindrical Batteries.
Shahid, S., and Agelin-Chaab, M. 2017.
Energies, Vol. 10, pp. 1157:4-17. [IF: 3.00].
Multipurpose Renewable Energy Resources based Hybrid Energy System for Remote Community in northern Ghana.
Adaramola, S., Quansah, D.A., Agelin-Chaab, M. and Paul, S.S. 2017.
Sustainable Energy Technologies and Assessments, Vol 22, pp. 161-170. [IF: 5.35]
Uneven temperature and voltage distributions due to rapid discharge rates and different boundary conditions for series-connected LiFePO 4 batteries.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Int. Comm. in Heat Mass Transfer, Vol. 81, pp. 210-217. [IF: 5.68]
Analysis of an innovative direct steam generation based parabolic trough collector plant hybridized with a biomass boiler.
Alhayek, B., Agelin-Chaab, M. and Reddy, B. 2017.
Int. J. Energy Research, Vol. 41(14), pp. 2236-2247. [IF: 5.16]
Thermal design and simulation of mini-channel cold plate for water cooled large sized prismatic Lithium-ion battery.
Panchal, S., Khasow, R., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Applied Thermal Engineering, Vol. 122, pp. 80-90. [IF: 5.30]
Cycling degradation testing and analysis of a LiFePO 4 battery at actual Conditions.
Panchal, S., McGrory, J., Kong, J., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Int. J. Energy Research, Vol. 41(15), pp. 2565-2575. [IF: 5.16]
Experimental investigation and simulation of temperature distribution in a 16Ah-LiMnNiCoO 2 battery during rapid discharge rates.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M.2017.
Heat and Mass Transfer, Vol. 53(3), pp. 937-946 [IF: 2.46]
Characteristics of Turbulent Flows Over Forward Facing Steps in Adverse Pressure Gradients Based on Two-Point Analyses.
Iftekhar, H. and Agelin-chaab, M. 2017.
J. Fluids Engineering (ASME), Vol. 139(11), pp. 114501 (6 pages). [IF: 2.00]
Transient Electrochemical Heat Transfer Modeling and Experimental Validation of a Large Sized LiFePO4/Graphite Battery.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Int. Journal of Heat and Mass Transfer, Vol. 109, pp. 1239-1251. [IF: 5.58]
Numerical modeling and experimental investigation of a prismatic battery subjected to water cooling.
Panchal, S., Khasow, R., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Numerical Heat Transfer, Part A: Applications, Vol. 71(6), pp. 626-637.[IF:2.93]
Experimental and simulated temperature variations in a LiFePO 4-20Ah battery during discharge process.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Applied Energy, Vol. 180, pp. 504-515. [IF: 9.75]
Feasibility of a hybrid solar andwind power system for an island community in The Bahamas.
Bingham, R.D., Agelin-Chaab, M. and Rosen, M.A. 2016.
Int. J. Renewable EnergyResearch, Vol. 6(3), pp. 951-963. [IF: 0.22]
Modeling of heat transfer from molten salt droplets using various gases.
Ghandehariun, S., Rosen, M. A., Agelin-Chaab, M. & Naterer, G.F. 2016.
Int. J. Heat and Mass Transfer, Vol. 105, pp. 140-146. [IF: 5.58]
Structure of turbulent flows over forward facing steps with adverse pressure gradient.
Iftekhar, H. and Agelin-chaab, M. 2016.
J. Fluids Engineering (ASME), Vol. 138(11), pp.111202-111202-12. [IF: 2.00]
Analysis and evaluation of a new renewable energy-based integrated system for residential applications.
Panchal, S., Dincer, I. and Agelin-Chaab, M. 2016.
Energy and Buildings, Vol. 128, pp. 900-910. [IF: 5.88]
Experimental and theoretical investigation of temperature distributions in a prismatic lithium-ion battery.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Int. J. Thermal Sciences, Vol. 99, pp. 204 – 212.
(On the list of most downloaded of the journal’s articles from October to Dec. 2015) [IF: 3.74]
Experimental study of turbulent offset jets.
Agelin-Chaab, M. 2016.
Int. J. Fluid Mechanics Research, Vol. 43(3), pp. 234-250. [IF: 0.20]
Integrated aero-thermal testing of a race car in a full scale climatic wind tunnel.
Abdel-Rahman, A., Agelin-Chaab, M. et al. 2016.
SAE International, Technical Paper # 2016-01-1588. https://doi.org/10.4271/2016-01-1588.
Thermal modeling and validation of temperature distributions in a prismatic lithium-ion battery at different discharge rates and varying boundary conditions.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Applied Thermal Engineering, Vol. 96, pp. 190-199. [IF: 5.30]
Comparative impact assessment study of various hydrogen production methods in terms of emissions.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2016.
Int. J. Hydrogen Energy, Vol. 41(19), pp. 8364-8375. [IF: 5.82]
Experimental temperature distributions in a prismatic lithium-ion battery at varying conditions.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Int. Communications in Heat and Mass Transfer, Vol. 71, pp. 35-43. [IF: 5.68]
Experimental and theoretical investigation of heat generation rates for a water cooled LiFePO4 battery.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Int. J. Heat and Mass Transfer, Vol. 101, pp. 1093 - 1102. [IF: 5.58]
Modeling a direct contact heat recovery process from molten salt droplets in various gases for thermochemical hydrogen production.
Ghandeharium, S., Rosen, M. and Agelin-Chaab, M. 2016.
WSEAS Transactions on Heat and Mass Transfer, Vol. 11, pp. 72-78.
Collings, W., Pao, W., and Agelin-Chaab, M. 2020.
SAE Int. J. Adv. & Curr Prac. in Mobility, 2(6), pp. 3293 - 3300, https://doi.org/10.4271/2020-01-0699
Selected as one of the best papers for the SAE International - World Congress Experience 2020.
Experimental and Numerical Studies of a Soft Impact Piezoelectric Energy Harvesting Using an MR Fluid.
Azangbebil, H. K., Djokoto, S. S., and Agelin-Chaab, M. 2020.
IEEE Sensors Journal, Vol. 20(19), pp. 11204-11211 [IF: 3.30]
Design of a Multigenerational System with Absorption Cooling for a Residential Community: A Case Study.
Bolt, A., Chea, B., Dincer, I., Agelin-Chaab, M. and Rosen M. 2020.
J. Energy Resources Technology (ASME), Vol. 143(6), pp. 1–11.[IF: 2.90]
A Critical Review of Synthetic Natural Gas Production Techniques and Technologies.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2020.
J. Natural Gas Science and Engineering Vol. 84, pp.103670. [IF:4.97]
Development of Clean Power Plant Integrated with Solar Farm for a Sustainable Community.
Seyam, S., Dincer, I. and Agelin-Chaab, M. 2020.
Energy Conversion and Management, Vol. 225, pp 113434. [IF: 9.71]
Modelling and Study of Magnetorheological Fluid Impact Base Frequency Enhancement for a Micro-Piezoelectric Energy Generator.
Djokoto, S. S., Azangbebil, H. K., Agelin-Chaab, M., Dragasius, E. and Juresnas, V. 2020.
Int. J. Green Energy, Vol. 17(9), pp. 529-539.[IF: 2.46]
Controlling of vibrations in micro-cantilever beam using a layer of active electrorheological fluid support.
Djokoto, S. S., Dragasius, E., Juresnas, V., and Agelin-Chaab, M. 2020.
IEEE Sensors Journal, Vol. 20 (8), pp. 4074 - 4079.[IF: 3.30]
Thermodynamic Analysis of a hybrid energy system using geothermal and solar energy sources with thermal storage in a residential building.
Seyam, S., Dincer, I., and Agelin-Chaab, M. 2020.
Energy Storage, Vol. 2(1), pp. 1-22.
Analysis of a clean hydrogen liquefaction plant integrated with a geothermal system.
Seyam, S., Dincer, I., and Agelin-Chaab, M. 2020.
J. Cleaner Production, Vol. 243, pp. 118562 [9.30]
Experimental study of hydrogen production process with aluminum and water.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2020.
Int. Journal of Hydrogen Energy, Vol. 45(28), 14232–14244. [IF: 5.82]
Experimental Study of a Thermal Cooling Technique for Cylindrical Batteries.
Wei, Y., and Agelin-Chaab, M. 2020.
Journal of Electrochemical Energy Conversion & Storage (ASME), 17(2): 021102 (13 pages) [IF: 2.01]
Energy and exergy analyses of hydrogen production process with aluminum and water chemical reaction.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2020.
Energy, Vol. 205, pp. [IF: 7.15]
Development and Experimental Analysis of a Hybrid Cooling Concept for Electric Vehicle Battery Packs.
Wei, Y., and Agelin-Chaab, M. 2019.
J. Energy Storage,Vol. 25, pp.100906 [IF: 6.58]
An Integrated Heat Recovery and Storage System for a Residential Building.
Bolt, A., Dincer, I., and Agelin-Chaab, M. 2019.
Energy Storage, Vol. 1(5), pp. 1–13.
A Meteorological Supersite for Aviation and Cold Weather Applications.
Gultepe, I., Agelin-Chaab, M., Komar, J. et al. 2019.
Pure Appl. Geophys, Vol. 176 (5), pp. 1977– 2015. https://doi.org/10.1007/s00024-018-1880-3 [IF: 2.34]
Application of Jets and Vortex Generators to Improve Air-cooling and Temperature Uniformity in a Simple Battery Pack.
Shahid, S., and Agelin-Chaab, M. 2018.
J. Thermal Science and Engineering Applications (ASME), Vol. 11(2), doi:10.1115/1.4041493 (16 pages). [IF: 1.47]
Whole Building Optimization of a Residential Home with PV and Battery Storage in The Bahamas.
Bingham, R., Agelin-Chaab, M. and Rosen M. 2018.
Renewable Energy, Vol. 132, pp. 1088-1103 [IF: 8.00]
Laminar-Turbulent Transition Flows of Non-Newtonian Slurries: Models Assessment.
Adane, K.F.K., and Agelin-Chaab, M. 2018
J. Fluids Engineering (ASME), Vol. 141(1),011104 (10 pages). [IF: 2.00]
Thermal and Electrical Performance Assessments of Lithium-Ion Battery Modules for an Electric Vehicle Under Actual Drive Cycles.
Panchal, S., Mathew, M., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2018.
Electric Power Systems Research, Vol. 163, pp.18-27 [IF: 3.41]
Experimental and Numerical Studies on Air Cooling and Temperature Uniformity in a Battery Pack.
Shahid, S., and Agelin-Chaab, M. 2018.
Int. J. Energy Research., Vol. 42(6), pp. 2246-2262 [IF: 5.16]
Experimental Investigation of a Novel Hybrid Cooling Method for Lithium-ion Batteries.
Wei, Y., and Agelin-Chaab, M. 2018,
Applied Thermal Engineering, Vol. 136,375-387 [IF: 5.30]
Design and Simulation of a Lithium-ion Battery at Large C-Rates and Varying Boundary Conditions through Heat Flux Distributions.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2018.
Measurement, Vol. 116, pp. 382-390. [IF: 3.93]
Development and analysis of a technique to improve air-cooling and temperature uniformity in a battery pack for cylindrical batteries.
Shahid, S., and Agelin-Chaab, M. 2018.
Thermal Science and Engineering Progress, Vol. 5, pp. 351-363.
Analysis of Cooling and Temperature Uniformity Effectiveness in a Battery Pack for Cylindrical Batteries.
Shahid, S., and Agelin-Chaab, M. 2017.
Energies, Vol. 10, pp. 1157:4-17. [IF: 3.00].
Multipurpose Renewable Energy Resources based Hybrid Energy System for Remote Community in northern Ghana.
Adaramola, S., Quansah, D.A., Agelin-Chaab, M. and Paul, S.S. 2017.
Sustainable Energy Technologies and Assessments, Vol 22, pp. 161-170. [IF: 5.35]
Uneven temperature and voltage distributions due to rapid discharge rates and different boundary conditions for series-connected LiFePO 4 batteries.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Int. Comm. in Heat Mass Transfer, Vol. 81, pp. 210-217. [IF: 5.68]
Analysis of an innovative direct steam generation based parabolic trough collector plant hybridized with a biomass boiler.
Alhayek, B., Agelin-Chaab, M. and Reddy, B. 2017.
Int. J. Energy Research, Vol. 41(14), pp. 2236-2247. [IF: 5.16]
Thermal design and simulation of mini-channel cold plate for water cooled large sized prismatic Lithium-ion battery.
Panchal, S., Khasow, R., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Applied Thermal Engineering, Vol. 122, pp. 80-90. [IF: 5.30]
Cycling degradation testing and analysis of a LiFePO 4 battery at actual Conditions.
Panchal, S., McGrory, J., Kong, J., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Int. J. Energy Research, Vol. 41(15), pp. 2565-2575. [IF: 5.16]
Experimental investigation and simulation of temperature distribution in a 16Ah-LiMnNiCoO 2 battery during rapid discharge rates.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M.2017.
Heat and Mass Transfer, Vol. 53(3), pp. 937-946 [IF: 2.46]
Characteristics of Turbulent Flows Over Forward Facing Steps in Adverse Pressure Gradients Based on Two-Point Analyses.
Iftekhar, H. and Agelin-chaab, M. 2017.
J. Fluids Engineering (ASME), Vol. 139(11), pp. 114501 (6 pages). [IF: 2.00]
Transient Electrochemical Heat Transfer Modeling and Experimental Validation of a Large Sized LiFePO4/Graphite Battery.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Int. Journal of Heat and Mass Transfer, Vol. 109, pp. 1239-1251. [IF: 5.58]
Numerical modeling and experimental investigation of a prismatic battery subjected to water cooling.
Panchal, S., Khasow, R., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2017.
Numerical Heat Transfer, Part A: Applications, Vol. 71(6), pp. 626-637.[IF:2.93]
Experimental and simulated temperature variations in a LiFePO 4-20Ah battery during discharge process.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Applied Energy, Vol. 180, pp. 504-515. [IF: 9.75]
Feasibility of a hybrid solar andwind power system for an island community in The Bahamas.
Bingham, R.D., Agelin-Chaab, M. and Rosen, M.A. 2016.
Int. J. Renewable EnergyResearch, Vol. 6(3), pp. 951-963. [IF: 0.22]
Modeling of heat transfer from molten salt droplets using various gases.
Ghandehariun, S., Rosen, M. A., Agelin-Chaab, M. & Naterer, G.F. 2016.
Int. J. Heat and Mass Transfer, Vol. 105, pp. 140-146. [IF: 5.58]
Structure of turbulent flows over forward facing steps with adverse pressure gradient.
Iftekhar, H. and Agelin-chaab, M. 2016.
J. Fluids Engineering (ASME), Vol. 138(11), pp.111202-111202-12. [IF: 2.00]
Analysis and evaluation of a new renewable energy-based integrated system for residential applications.
Panchal, S., Dincer, I. and Agelin-Chaab, M. 2016.
Energy and Buildings, Vol. 128, pp. 900-910. [IF: 5.88]
Experimental and theoretical investigation of temperature distributions in a prismatic lithium-ion battery.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Int. J. Thermal Sciences, Vol. 99, pp. 204 – 212.
(On the list of most downloaded of the journal’s articles from October to Dec. 2015) [IF: 3.74]
Experimental study of turbulent offset jets.
Agelin-Chaab, M. 2016.
Int. J. Fluid Mechanics Research, Vol. 43(3), pp. 234-250. [IF: 0.20]
Integrated aero-thermal testing of a race car in a full scale climatic wind tunnel.
Abdel-Rahman, A., Agelin-Chaab, M. et al. 2016.
SAE International, Technical Paper # 2016-01-1588. https://doi.org/10.4271/2016-01-1588.
Thermal modeling and validation of temperature distributions in a prismatic lithium-ion battery at different discharge rates and varying boundary conditions.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Applied Thermal Engineering, Vol. 96, pp. 190-199. [IF: 5.30]
Comparative impact assessment study of various hydrogen production methods in terms of emissions.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2016.
Int. J. Hydrogen Energy, Vol. 41(19), pp. 8364-8375. [IF: 5.82]
Experimental temperature distributions in a prismatic lithium-ion battery at varying conditions.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Int. Communications in Heat and Mass Transfer, Vol. 71, pp. 35-43. [IF: 5.68]
Experimental and theoretical investigation of heat generation rates for a water cooled LiFePO4 battery.
Panchal, S., Dincer, I., Agelin-Chaab, M., Fraser, R., & Fowler, M. 2016.
Int. J. Heat and Mass Transfer, Vol. 101, pp. 1093 - 1102. [IF: 5.58]
Modeling a direct contact heat recovery process from molten salt droplets in various gases for thermochemical hydrogen production.
Ghandeharium, S., Rosen, M. and Agelin-Chaab, M. 2016.
WSEAS Transactions on Heat and Mass Transfer, Vol. 11, pp. 72-78.
Turbulent flows over forward facing steps with surface roughness.
Shao, W. J. and Agelin-chaab, M. 2015.
J. Fluids Engineering (ASME), Vol. 138(2), pp. 021103 (12 pages). [IF: 2.00]
Experimental investigation of underbody thermal and aerodynamic flow-field features.
Khasow, R., Best, S., Agelin-Chaab, M. et al. 2015.
SAE Int. J. Passeng. Cars - Mech. Syst., Vol. 8(1), pp. 146-154.
Selected as one of the best papers for the SAE International.
Thermodynamic analysis of hydraulic braking energy recovery systems for a vehicle.
Panchal, S., Dincer, I. and Agelin-Chaab, M. 2015.
J. Energy Resources Technology (ASME), Vol. 138 (1), pp. 011601 (9 pages). [IF: 2.90]
Environmental impact assessment and comparison of some hydrogen production options.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2015.
Int. J. Hydrogen Energy, Vol. 40(21), pp. 6976–6987. [IF: 5.82]
Automotive underbody diffuser effects on thermal management.
Khasow, R. and Agelin-chaab, M. 2015.
Int. J. Process Systems Engineering, Vol. 3(2), pp. 110-125.
Structure of turbulent flows over two-dimensional bluff bodies inspired by a pickup truck geometry.
Agelin-Chaab, M. 2014.
Int. J. Heat and Fluid Flow, Vol. 50, pp. 417-430. [IF: 2.79]
Development of an integrated renewable energy system for multi-generation.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2014.
Energy, Vol. 78, pp. 196–204. [IF: 7.15]
Analysis of hybrid energy Systems for application in southern Ghana.
Adaramola, M.S., Agelin-Chaab, M. and Paul, S.S. 2014.
Energy Conversion and Management, Vol. 88, 284-295. [IF: 9.71]
Energy and exergy analyses of an integrated solar heat pump system.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2014.
Applied Thermal Engineering, Vol. 73(1), pp. 557- 564. [IF: 5.30]
Assessment of wind power generation along the coast of Ghana.
Adaramola, M.S., Agelin-Chaab, M. and Paul, S.S. 2014.
Energy Conversion and Management, Vol. 77, pp. 61- [IF: 9.71]
Open channel turbulent flow past rectangular cylinders at incidence.
Agelin-Chaab, M. and Tachie, M.F. 2013.
ASCE J. Hydraulic Engineering, Vol. 139(12), pp. 1309- [IF: 2.82]
Near wake structure of wall-mounted finite cylinders In shallow open channel flow.
Agelin-Chaab, M. and Paul, S.S. 2013.
Int. J. Fluid Mechanics Research, Vol. 40(2), 168-183. [IF: 0.20]
Particle image velocimetry measurements in curved turbulent jets produced from a slot diffuser.
Essel, E.E., Tachie, M.F., Agelin-Chaab, M. et al. 2013.
Experimental Thermal and Fluid Science, Vol. 49(2), pp. 169- 184. [IF: 3.23]
Experimental study of turbulent flow in a slot diffuser.
Essel, E.E., Tachie, M.F., Agelin-Chaab, M., Ampadu-Mintah, A.A., Koupriyanov, M. and Tully, B. September 2012.
In proceedings of the 7 th International Symposium on Turbulence, Heat and Mass Transfer , Palermo, Italy.
Low Reynolds Number Open Channel Flows over a Backward Facing Step.
Ampadu-Mintah, A.A, Tachie, M.F. and Agelin-Chaab, M. September 2012.
Proceedings of the ASME 2012 Fluids Engineering Summer Meeting, FEDSM2012, Rio Grande, Puerto Rico.
Roughness effects on separated and reattached open channel turbulent flow.
Ampadu-Mintah, A.A, Tachie, M.F. and Agelin-Chaab, M. September 2012.
In proceedings of the 7 th International Symposium on Turbulence, Heat and Mass Transfer , Palermo, Italy.
An Experimental study of plane free jet from a vertical slot diffuser.
Essel, E.E., Tachie, M.F., Agelin-Chaab, M., Koupriyanov, M. and Tully, B. June 2012.
In proceedings of the Canadian Society of Mechanical Engineers (CSME) International Congress, Winnipeg, Canada.
Characteristics of turbulent three-dimensional offset jets.
Agelin-Chaab, M. and Tachie, M. F. 2011.
J. Fluids Engineering (ASME), Vol. 133(5),pp. 051203 (9 pages). [IF: 2.00]
Characteristics of turbulent three-dimensional wall jets.
Agelin-Chaab, M. and Tachie, M. F. 2011.
J. Fluids Engineering (ASME), Vol. 133(2), pp. 021201 (12 pages). [IF: 2.00]
Characteristics and structure of turbulent 3d offset jets.
Agelin-Chaab, M. and Tachie, M. F. 2011.
Int. J. Heat and Fluid Flow, Vol. 32(3), pp. 608-620.
Selected Paper from 8th International ERCOFTAC Symposium Engineering Turbulence Modeling and Measurements. [IF: 2.79]
Shao, W. J. and Agelin-chaab, M. 2015.
J. Fluids Engineering (ASME), Vol. 138(2), pp. 021103 (12 pages). [IF: 2.00]
Experimental investigation of underbody thermal and aerodynamic flow-field features.
Khasow, R., Best, S., Agelin-Chaab, M. et al. 2015.
SAE Int. J. Passeng. Cars - Mech. Syst., Vol. 8(1), pp. 146-154.
Selected as one of the best papers for the SAE International.
Thermodynamic analysis of hydraulic braking energy recovery systems for a vehicle.
Panchal, S., Dincer, I. and Agelin-Chaab, M. 2015.
J. Energy Resources Technology (ASME), Vol. 138 (1), pp. 011601 (9 pages). [IF: 2.90]
Environmental impact assessment and comparison of some hydrogen production options.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2015.
Int. J. Hydrogen Energy, Vol. 40(21), pp. 6976–6987. [IF: 5.82]
Automotive underbody diffuser effects on thermal management.
Khasow, R. and Agelin-chaab, M. 2015.
Int. J. Process Systems Engineering, Vol. 3(2), pp. 110-125.
Structure of turbulent flows over two-dimensional bluff bodies inspired by a pickup truck geometry.
Agelin-Chaab, M. 2014.
Int. J. Heat and Fluid Flow, Vol. 50, pp. 417-430. [IF: 2.79]
Development of an integrated renewable energy system for multi-generation.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2014.
Energy, Vol. 78, pp. 196–204. [IF: 7.15]
Analysis of hybrid energy Systems for application in southern Ghana.
Adaramola, M.S., Agelin-Chaab, M. and Paul, S.S. 2014.
Energy Conversion and Management, Vol. 88, 284-295. [IF: 9.71]
Energy and exergy analyses of an integrated solar heat pump system.
Suleman, F., Dincer, I. and Agelin-Chaab, M. 2014.
Applied Thermal Engineering, Vol. 73(1), pp. 557- 564. [IF: 5.30]
Assessment of wind power generation along the coast of Ghana.
Adaramola, M.S., Agelin-Chaab, M. and Paul, S.S. 2014.
Energy Conversion and Management, Vol. 77, pp. 61- [IF: 9.71]
Open channel turbulent flow past rectangular cylinders at incidence.
Agelin-Chaab, M. and Tachie, M.F. 2013.
ASCE J. Hydraulic Engineering, Vol. 139(12), pp. 1309- [IF: 2.82]
Near wake structure of wall-mounted finite cylinders In shallow open channel flow.
Agelin-Chaab, M. and Paul, S.S. 2013.
Int. J. Fluid Mechanics Research, Vol. 40(2), 168-183. [IF: 0.20]
Particle image velocimetry measurements in curved turbulent jets produced from a slot diffuser.
Essel, E.E., Tachie, M.F., Agelin-Chaab, M. et al. 2013.
Experimental Thermal and Fluid Science, Vol. 49(2), pp. 169- 184. [IF: 3.23]
Experimental study of turbulent flow in a slot diffuser.
Essel, E.E., Tachie, M.F., Agelin-Chaab, M., Ampadu-Mintah, A.A., Koupriyanov, M. and Tully, B. September 2012.
In proceedings of the 7 th International Symposium on Turbulence, Heat and Mass Transfer , Palermo, Italy.
Low Reynolds Number Open Channel Flows over a Backward Facing Step.
Ampadu-Mintah, A.A, Tachie, M.F. and Agelin-Chaab, M. September 2012.
Proceedings of the ASME 2012 Fluids Engineering Summer Meeting, FEDSM2012, Rio Grande, Puerto Rico.
Roughness effects on separated and reattached open channel turbulent flow.
Ampadu-Mintah, A.A, Tachie, M.F. and Agelin-Chaab, M. September 2012.
In proceedings of the 7 th International Symposium on Turbulence, Heat and Mass Transfer , Palermo, Italy.
An Experimental study of plane free jet from a vertical slot diffuser.
Essel, E.E., Tachie, M.F., Agelin-Chaab, M., Koupriyanov, M. and Tully, B. June 2012.
In proceedings of the Canadian Society of Mechanical Engineers (CSME) International Congress, Winnipeg, Canada.
Characteristics of turbulent three-dimensional offset jets.
Agelin-Chaab, M. and Tachie, M. F. 2011.
J. Fluids Engineering (ASME), Vol. 133(5),pp. 051203 (9 pages). [IF: 2.00]
Characteristics of turbulent three-dimensional wall jets.
Agelin-Chaab, M. and Tachie, M. F. 2011.
J. Fluids Engineering (ASME), Vol. 133(2), pp. 021201 (12 pages). [IF: 2.00]
Characteristics and structure of turbulent 3d offset jets.
Agelin-Chaab, M. and Tachie, M. F. 2011.
Int. J. Heat and Fluid Flow, Vol. 32(3), pp. 608-620.
Selected Paper from 8th International ERCOFTAC Symposium Engineering Turbulence Modeling and Measurements. [IF: 2.79]
Turbulent flows over aligned and inclined ribs.
Tachie, M. F. and Agelinchaab, M. 2010.
Springer Berlin, pp. 13-20.
Papers from IUTAM Symposium on The Physics of Wall-Bounded Flows.
PIV study of turbulent flow through a porous medium.
Bejatovic, S., Tachie, M. F., Agelinchaab, M. and Paul, S. S. 2009.
Notes on Numerical Fluid Mechanics and Multidisciplinary Design, Vol. 110, pp. 71-78.
Selected from Second International Conference on Turbulence and Interaction.
Structure of turbulent flow over 90 o and 45 o transverse ribs.
Tachie, M. F., Paul, S. S., Agelinchaab, M. and Shah, M. K. 2009.
J. Turbulence, Vol. 10(20), pp. 1-23. Invited Paper. [IF: 1.40]
PIV study of adverse and favorable pressure gradient turbulent flows over transverse ribs.
Agelinchaab, M. and Tachie, M. F. 2008.
J. Fluids Engineering (ASME), Vol.130(11), pp. 111305 (12 pages). [IF: 2.00]
Turbulent wake of rectangular cylinder near a plane wall and a free surface.
Agelinchaab, M., Tsikata, J. M., Tachie, M. F. and Adane, K. K. 2008.
AIAA J., Vol. 46(1), pp.104-117. [IF: 2.13]
PIV study of separated and reattached open channel flow over surface mounted blocks.
Agelinchaab, M. and Tachie, M. F. 2008.
J. Fluids Engineering (ASME), Vol. 130(6), 061206 (9 pages).
Among the ASME’s “Top 10 Most Downloaded Articles” in June 2008. [IF: 2.00]
Characteristics of the Flow over a NACA0012 Airfoil at Low Reynolds Numbers
Derksen, R.W., Agelinchaab, M. and Tachie, M. F. 2008.
WIT Transactions on Engineering Sciences, Vol. 59, pp. 143-152.
Influence of PIV interrogation area on turbulence statistics up to fourth order moments in smooth and rough wall turbulent flows.
Shah, M. K., Agelinchaab, M. and Tachie, M. F. 2008.
Experimental Thermal and Fluid Science, Vol. 32(2), pp. 725-747. [IF: 3.23]
Turbulent flow over transverse rib in open channel with converging side walls.
Tachie, M. F., Agelinchaab, M. and Shah, M. K. 2007.
Int. J. Heat and Fluid Flow, Vol. 28(4), 683-707. [IF: 2.79]
Open channel turbulent flow over hemispherical ribs.
Agelinchaab, M. and Tachie, M. F. 2006.
Int. J. Heat and Fluid Flow, Vol. 27(6), pp. 1010-1027. [IF: 2.79]
Velocity measurement of flow through a model three-dimensional porous medium.
Agelinchaab, M., Tachie, M. F. and Ruth, D. W. 2006.
Physics of Fluids, Vol. 18(1), pp. 017105- 017116. [IF: 3.52]
Tachie, M. F. and Agelinchaab, M. 2010.
Springer Berlin, pp. 13-20.
Papers from IUTAM Symposium on The Physics of Wall-Bounded Flows.
PIV study of turbulent flow through a porous medium.
Bejatovic, S., Tachie, M. F., Agelinchaab, M. and Paul, S. S. 2009.
Notes on Numerical Fluid Mechanics and Multidisciplinary Design, Vol. 110, pp. 71-78.
Selected from Second International Conference on Turbulence and Interaction.
Structure of turbulent flow over 90 o and 45 o transverse ribs.
Tachie, M. F., Paul, S. S., Agelinchaab, M. and Shah, M. K. 2009.
J. Turbulence, Vol. 10(20), pp. 1-23. Invited Paper. [IF: 1.40]
PIV study of adverse and favorable pressure gradient turbulent flows over transverse ribs.
Agelinchaab, M. and Tachie, M. F. 2008.
J. Fluids Engineering (ASME), Vol.130(11), pp. 111305 (12 pages). [IF: 2.00]
Turbulent wake of rectangular cylinder near a plane wall and a free surface.
Agelinchaab, M., Tsikata, J. M., Tachie, M. F. and Adane, K. K. 2008.
AIAA J., Vol. 46(1), pp.104-117. [IF: 2.13]
PIV study of separated and reattached open channel flow over surface mounted blocks.
Agelinchaab, M. and Tachie, M. F. 2008.
J. Fluids Engineering (ASME), Vol. 130(6), 061206 (9 pages).
Among the ASME’s “Top 10 Most Downloaded Articles” in June 2008. [IF: 2.00]
Characteristics of the Flow over a NACA0012 Airfoil at Low Reynolds Numbers
Derksen, R.W., Agelinchaab, M. and Tachie, M. F. 2008.
WIT Transactions on Engineering Sciences, Vol. 59, pp. 143-152.
Influence of PIV interrogation area on turbulence statistics up to fourth order moments in smooth and rough wall turbulent flows.
Shah, M. K., Agelinchaab, M. and Tachie, M. F. 2008.
Experimental Thermal and Fluid Science, Vol. 32(2), pp. 725-747. [IF: 3.23]
Turbulent flow over transverse rib in open channel with converging side walls.
Tachie, M. F., Agelinchaab, M. and Shah, M. K. 2007.
Int. J. Heat and Fluid Flow, Vol. 28(4), 683-707. [IF: 2.79]
Open channel turbulent flow over hemispherical ribs.
Agelinchaab, M. and Tachie, M. F. 2006.
Int. J. Heat and Fluid Flow, Vol. 27(6), pp. 1010-1027. [IF: 2.79]
Velocity measurement of flow through a model three-dimensional porous medium.
Agelinchaab, M., Tachie, M. F. and Ruth, D. W. 2006.
Physics of Fluids, Vol. 18(1), pp. 017105- 017116. [IF: 3.52]
